Laborer/Assembler (BraunAbility Continuing to GROW)
Winamac, IN Winamac, IN Full-time Full-time From $18.
62 an hour From $18.
62 an hour
Summary:
Assembler/Laborer completes assembly processes according to established job breakdown sheets by performing the following duties.
Essential Duties and
Responsibilities:
Read, learn, understand and interpret work instructions, and other instructions written or verbal, to complete assembly of products according to established guidelines and quality standards Use a variety of hand and power tools following appropriate methods and procedures to complete mechanical assembly of products.
Inspect parts and products as necessary, during or after assembly, according to established guidelines and quality standards.
Maintain a clean and organized work area and maintain all equipment according to established guidelines and quality standards.
Practice problem solving and troubleshooting techniques as part of a team responsible for continuous improvement to products and processes.
Cross train in other areas of department as needed.
Maintain a positive work atmosphere by acting and communicating in a manner so that you get along with customers, co-workers and management.
Continue to drive the LEAN knowledge and use the tools to identify and assist with continuous improvement.
Comply with safety regulations and maintain clean and orderly work areas.
Qualifications:
To perform this job successfully, an individual must be able to perform each essential duty satisfactorily.
The requirements listed below are representative of the knowledge, skill, and/or ability required.
Must be willing to learn and practice continuous improvement techniques such as 5s, one piece flow, value stream mapping, set-up reduction, and more.
Education:
High school diploma or general education degree (GED) required.
Language:
Ability to read and comprehend simple instructions, short correspondence, and memos in English.
Ability to write simple correspondence.
Ability to effectively present information in one-on-one and small group situations to customers and other employees of the organization.
Mathematical Skills:
Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals.
Ability to read blue prints and a tape measure.
Reasoning Ability:
Ability to apply common sense and understanding to carry out detailed but uninvolved written or oral instructions.
Ability to deal with problems involving a few concrete variables in standardized situations.
Physical Demands:
The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job.
While performing the duties of this job, the employee is regularly required to stand.
The employee is frequently required to walk; use hands to finger, handle or feel; reach with hands and arms and talk or hear.
The employee is occasionally required to sit; climb or balance and stoop, kneel, crouch, or crawl.
The employee must frequently lift and/or move up to 50 pounds.
Work Environment:
The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job.
While performing the duties of this job the employee is regularly exposed to moving mechanical parts.
The noise level in the work environment is usually moderate.
Job Type:
Full-time Pay:
From $18.
62 per hour
Benefits:
401(k) 401(k) matching Dental insurance Employee assistance program Employee discount Flexible schedule Health insurance Health savings account Life insurance Paid time off Retirement plan Vision insurance Schedule:
8 hour shift Work Location:
In person.
Estimated Salary: $20 to $28 per hour based on qualifications.
62 an hour From $18.
62 an hour
Summary:
Assembler/Laborer completes assembly processes according to established job breakdown sheets by performing the following duties.
Essential Duties and
Responsibilities:
Read, learn, understand and interpret work instructions, and other instructions written or verbal, to complete assembly of products according to established guidelines and quality standards Use a variety of hand and power tools following appropriate methods and procedures to complete mechanical assembly of products.
Inspect parts and products as necessary, during or after assembly, according to established guidelines and quality standards.
Maintain a clean and organized work area and maintain all equipment according to established guidelines and quality standards.
Practice problem solving and troubleshooting techniques as part of a team responsible for continuous improvement to products and processes.
Cross train in other areas of department as needed.
Maintain a positive work atmosphere by acting and communicating in a manner so that you get along with customers, co-workers and management.
Continue to drive the LEAN knowledge and use the tools to identify and assist with continuous improvement.
Comply with safety regulations and maintain clean and orderly work areas.
Qualifications:
To perform this job successfully, an individual must be able to perform each essential duty satisfactorily.
The requirements listed below are representative of the knowledge, skill, and/or ability required.
Must be willing to learn and practice continuous improvement techniques such as 5s, one piece flow, value stream mapping, set-up reduction, and more.
Education:
High school diploma or general education degree (GED) required.
Language:
Ability to read and comprehend simple instructions, short correspondence, and memos in English.
Ability to write simple correspondence.
Ability to effectively present information in one-on-one and small group situations to customers and other employees of the organization.
Mathematical Skills:
Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals.
Ability to read blue prints and a tape measure.
Reasoning Ability:
Ability to apply common sense and understanding to carry out detailed but uninvolved written or oral instructions.
Ability to deal with problems involving a few concrete variables in standardized situations.
Physical Demands:
The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job.
While performing the duties of this job, the employee is regularly required to stand.
The employee is frequently required to walk; use hands to finger, handle or feel; reach with hands and arms and talk or hear.
The employee is occasionally required to sit; climb or balance and stoop, kneel, crouch, or crawl.
The employee must frequently lift and/or move up to 50 pounds.
Work Environment:
The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job.
While performing the duties of this job the employee is regularly exposed to moving mechanical parts.
The noise level in the work environment is usually moderate.
Job Type:
Full-time Pay:
From $18.
62 per hour
Benefits:
401(k) 401(k) matching Dental insurance Employee assistance program Employee discount Flexible schedule Health insurance Health savings account Life insurance Paid time off Retirement plan Vision insurance Schedule:
8 hour shift Work Location:
In person.
Estimated Salary: $20 to $28 per hour based on qualifications.
|
|
 | |
